BPS Fine & Superfine

BPS is a polymer modified portland cement product designed to be used with conventional or one coat portland cement plaster wall systems.

Features and Uses:
BPS may be used for the following applications:

Bonding and plastering EPS foam shapes:
Patching hairline cracks in portland cement plaster.
Skim coating directly over portland cement.
A mesh embedment coat for use over portland cement.
It is an all in one mix so every batch is accurate.
It is flexible and water resistant.
Provides superb adhesion to portland cement.
Provides an excellent substrate for acrylic finishes to adhere to.

BPS is packaged in 50 lb / 22.7 kg sacks.  Fifty-six sacks per pallet.

Sands Blends:
BPS is available in a “fine” and “superfine” aggregate. 

Coverage when used for adhering EPS shapes:
Coverage at 1/16” is approximately 80 square feet per bag.  Porosity of substrates will affect the coverage. The 'superfine' aggregate will get slightly better coverage then the 'fine' aggregate. 

Embedding mesh will require a thicker application to achieve full embedment of the mesh. 

It is also recommended to increase the thickness of the application over EPS foam shapes to provide more durability.

Each 50-lb. sack of BPS is mixed with 1.25 gallons of potable water in a clean pail and drill mixed with a paddle mixer. Initial mixing time is approximately 3 minutes or until the material is thoroughly wet.  The material shall stand for 5 minutes.  Add additional water as needed (up to 6 ounces.) and mix for one minute or just the time it takes to disperse the additional water. 

Application as a skim coat:
Apply 1/16” thick BPS with a steel trowel over portland cement. Smooth plaster with trowel.

Application as EPS adhesive:
All surfaces to receive EPS shapes shall be moistened before application.  The surface of the EPS shape shall also be scored to provide a good key for the adhesive.  Apply BPS with ½” x ½” notched trowel to the back of the EPS shape. Coverage should be 100% with BPS. Press firmly into place.

Application as an embedment coat for mesh:
Embed mesh in a 1/16” thick layer of BPS. Use trowel to apply pressure to fully embed the mesh.  Smooth plaster with trowel. An additional coat may be required if mesh is visible.

Application as a patching plaster:
BPS Kote may be directly troweled over hairline cracks in cement brown coats before the application of a BPS skim coat.

For cracks larger then hairline (1/64”) or 'dynamic' cracks, work BPS into the crack  then apply 2” fiberglass tape over the crack.  Trowel BPS over the top and another 6” to 8” in al directions from the repaired area. Feather the edges to blend into the cement substrate.  Skim coat entire surface as described above.

The product requires a minimum of forty-eight (48) hours moist curing.  Environmental conditions such as heat, wind and low humidity will require additional curing.

A variety of finishes such as standard acrylic paints, textured acrylic finishes or elastomeric coatings may be applied over BPS Kote. The recommendations of the finish coat manufacturer shall be followed regarding base coat preparation, acceptable pH levels, bonding, application and curing of their finish.

Do not add accelerator, air entrainment or other admixtures to BPS Kote without written permission from an authorized manufacturer of Western Blended Products.

Do not apply BPS on surfaces sloped less then 30 degrees or surfaces that are below grade or subject to hydrostatic pressure.

Do not apply when surface or ambient temperatures are at or below 40ºF / 4.4ºC or above 100ºF / 34ºC. Do not apply to surfaces that are contaminated with bond breakers, oils or other matter that may affect the performance of the product. Do not apply BPS Kote if conditions are expected to be above or below the specified temperature range within 24 hours of application. Do not add additional ingredients to BPS Kote   without specific written approval from an authorized manufacturer of Western Blended Products.

BPS Kote shall be kept indoors or if stored outdoors, shall be adequately covered to keep dry and be stored off the ground.

Manufacturers or Western Blended Products (WBP) warrants its products to be of merchantable quality and suitable for the general purpose for which they were intended, when applied in accordance with WBP instructions.  Manufacturers of WBP do not warrant its products to be suitable for any purpose or use other than for which they were intended.  Liability under this warranty is limited to supplying new material without charge, or at manufacturers of WBP option, to a refund of the purchase price.  In the event of a claim under this warranty, written notice must be given to the originating plant of the WBP goods at the address shown hereon.  This limited warranty is issued and accepted in lieu of all other expressed warranties, and expressly excludes liability for consequential damages.  Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations and exclusions may not apply to you.  This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

December 13, 2007